Morley POWER WAH (PWO) Manuel d'utilisateur télécharger pdf

THANK YOU!

For purchasing a Morley® pedal. You now

own the best Wah pedal made!

Please take a few minutes to familiarize

yourself with the features of your new pedal.

With common sense handling, it should last for

years. We know you will appreciate the rugged

construction of your Morley®. Most of all, we

hope you enjoy using it as much as we enjoyed

building it.

OPERATION

The Wah Mode is activated by pushing the

Wah switch. The Power Wah is equipped with

true bypass. This means that when the pedal is

in bypass mode, your original guitar signal is

uninterrupted. We’ve maintained the full, thick

sound and wide bandwidth of previous Morley

WAH pedals and added more reactive sound.

Now you can make your guitar talk and sing

similar to the sounds of Hendrix, Clapton and

other wah wah masters.

CONNECTIONS

9V: Use Morley’s 9 VDC 300 milliamp

regulated adapter only.

IN: Input jack. Plug instrument into this jack

using 1/4” guitar cable.

OUT: Connect amplifier to this jack using a

1/4” guitar cable.

NOTE: You’ll find cords fit very tightly into

our input and output jacks. The tight fit helps

prevent the cord from becoming accidentally

unplugged from the pedal. Make sure the cords

are completely plugged in for best results.

AC ADAPTER

Use Morley’s 9VDC 300 milliamp regulated

adapter only. Using a non-regulated adapter

could cause a low frequency hum in your

amplifier and may damage the pedal.

BATTERY

The PWO is designed to use one 9 volt battery

when not using an adapter. We suggest you use

a good quality alkaline battery.

To prolong battery life, unplug your cord

completely from the input jack when not using

the pedal. When the pedal is not used for

extended periods, we recommend you remove

the battery from the pedal or replace it every

six months to prevent leakage problems.

BATTERY REPLACEMENT

When the battery becomes weak, the overall

wah will become weak and your signal may

become slightly distorted.

Remove the battery door located on the bottom

of the pedal (a short cord is attached to the

door to help prevent loss). Once the door is off,

the old battery can be removed from the battery

snap and a new battery plugged in. Make sure

the polarity (+/-) is correct before inserting the

new battery.

When you replace the battery door, you will

notice it fits very tightly against the battery.

This prevents the battery from rattling inside

the pedal.

WARRANTY

All Morley® pedals are warranted for two

years from date of purchase. To obtain

warranty service contact the store where

purchased.

SPECIFICATIONS

POWER: 9 Volt Battery or 9VDC 300

milliamp regulated adapter (center pin is

negative)

CURRENT DRAW: 5 mA @ 9 VDC

WEIGHT: 2.9 lb./ 1.32 kg

Here is a general recommendation for

hooking up a WAH with other effects:

• NOTE: This pedal is not intended for use

through an effects loop (send and return).

1 2

THANK YOU! 1
Power Wah 2

Résumé du contenu

Page 1 - THANK YOU!

THANK YOU! For purchasing a Morley® pedal. You now own the best Wah pedal made! Please take a few minutes to familiarize yourself with the features of

Page 2 - Power Wah

FEATURES • WAH On/Off Switch: This switch turns the WAH effect “on” or “off”. • Electro-Optical: The light from an LED (Light Emitting Diode)

Commentaires sur ces manuels

Pas de commentaire

Morley POWER WAH (PWO) Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Instruments de musique Morley POWER WAH (PWO). Morley POWER WAH (PWO) User Manual [en] [pl] [cs] [de] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Morley POWER WAH (PWO)